Fluidmaster 400LSRP14 Guide d'installation télécharger pdf

+OR

SHANK/

CONE

WASHER

COUPLING

NUT

REFILL CLIP

OR ANGLE

ADAPTER

LOCKNUT

Roller & Hose

Clamp

ASSEMBLY PARTS

LEAK SENTRY

DEVICE

Roller & Hose Clamp

Hose Clamps

MEASURE

HEIGHT ONLY; DO

NOT INSTALL

“CL”

MARK

DO NOT

MOVE

LOCK RING

FLUIDMASTER

400LS FILL

VALVE WITH LEAK SENTRY

TECHNOLOGY INSTALLATION

INSTRUCTIONS

START HERE

IMPORTANT: A flapper with a plastic or metal chain is

recommended for the Leak Sentry

to maintain its settings.

Flappers with nylon or vinyl straps will stretch and cause

Leak Sentry

to work improperly.

(Replace with a flapper like the Fluidmaster 501 or 502.)

Flush out tank and sponge

dry. Remove water supply

coupling nut and locknut

from under tank.

Remove fill valve from tank.Turn off water supply.

(Clockwise)

PART#4-753, Rev. 3, 02/09

DO NOT USE

TOOLS NEEDED

Push the cone washer out with

your thumb or with scissors

cut the four connections

between the shank & cone

washers. Set cone washer aside.

Prepare Valve

for Installation

DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING

BLEACH OR CHLORINE. Use of such products will: (1) RESULT IN DAMAGE to tank

components and MAY CAUSE FLOODING and PROPERTY DAMAGE and (2) VOID

FLUIDMASTER WARRANTY. DO NOT overtighten nuts or tank/bowl may crack.

Fluidmaster Flush ’n Sparkle

Toilet Bowl Cleaning System is recommended for

those choosing to use in-tank bowl cleaners and WILL NOT VOID the FLUIDMASTER WARRANTY because

it will not damage the components.

400LS WATER-SAVING FEATURES

Prevents wasteful refills in leaky tanks.

The Leak Sentry

device alerts you to a tank leak, typically caused by a faulty flapper.

If there is a tank leak, the float cup will not drop to refill the tank until the tank lever is

pushed. On the first flush attempt, the valve will simply refill the empty tank; only then

will you receive a complete flush. This will continue to occur until the tank leak is fixed.

The Adjustable Refill allows you to adjust the amount of water going into the bowl,

eliminating water waste due to the bowl being overfilled.

WARNING

Because drop-in cleaners used in the tank can result in damaged

tank parts (see WARNING above), Fluidmaster recommends the

use of Flush ’n Sparkle

Toilet Bowl Cleaning System (Models

8100, 8200 or 8300). It cleans the bowl without harming tank

parts by isolating the cleaner from the tank water, releasing it

only to the bowl where it is needed. Cartridges supply more than

1,000 flushes and are a snap to replace.

Remove Fill Valve from Tank

continued...

Water-Saving Feature: Hooking Up the Leak Sentry

Chain

Testing Leak Sentry

Water-Saving Feature: Roller Clamp

Check bowl water level by flushing toilet. If bowl appears to be full but continues to

fill, the valve may be overfilling the bowl causing excess water to siphon down the

trapway. Adjust amount of water going down into the bowl as follows: Fill the bowl

with a gallon of water. Wait 3 minutes until the bowl water level recedes down and

stops. With a pencil, draw a line at the top of the water level in bowl. Now flush the

toilet. If the valve is still filling and the water is up to the line in the bowl, then the

amount of water going into the bowl is too high and needs to be adjusted. Adjust

the refill by turning the roller clamp with thumb to the next lower number. Flush

the toilet; adjust until water level in bowl is at the pencil mark when the fill valve

shuts off. If valve shuts off and bowl is not full, adjust by turning the roller clamp

to a higher number. Repeat until water in bowl is up to line. “O” on roller clamp

equals no refill to bowl.

Flushing Out the Debris:

Hold

a cup over the uncapped valve

to prevent splashing. Turn water

supply full on and off a few

times. Leave water supply off.

Check for leaks. Tighten nuts

just enough to stop leaking.

Place cap assembly on top of

gray valve body by aligning

cap arm and adjustment rod

next to refill hose.

Press down on top cap rotat-

ing top & arm clockwise to

locked position.

Turn on water supply.

IMPORTANT: Submerge the

float cup under the water for

30 seconds. Adjust water level

by turning water level

adjustment screw. To raise–

turn clockwise; to lower –

counterclockwise.

For your convenience, the roller clamp

and hose clamps are pre-assembled to the

refill hose. Attach one end of hose to refill

clip and slide clip to right side of overflow

pipe. Attach other end of hose to nipple on

fill valve with a slight arching (see picture

to the left). Cut tube if necessary. Squeeze

tabs of hose clamp and move clamp to

end of hose, over the fill valve nipple, then

release tabs. Do not shove refill tube down

overflow pipe. This will cause water loss.

FLAPPER CHAIN HOOK-UP

Lift tank lever all the way up inside tank.

Hold tank lever there. Pull flapper chain

tight so the flapper is lifted as high as it

can go and attach chain to hole in lever

directly above flapper. Make sure flapper

chain is straight.

Make sure flapper is closed on seat. If

not, you may need to lengthen the flapper

chain by a link or two to allow flapper to

close and seal tank.

TROUBLESHOOTING

FLUSHING OUT DEBRIS

30800 Rancho Viejo Road

San Juan Capistrano, CA 92675

www.uidmaster.com

800-631-2011

Remove cap assembly

Flush out valve

Replace cap assembly

WARRANTY

This Fluidmaster

product has a limited

warranty for a period of 5 years. For complete

warranty details, please visit our website at

www.fluidmaster.com

FILL VALVE WILL NOT TURN OFF.

IMPORTANT: Sand and rust move through

water pipes. Always clear debris from

water lines. Repeat steps “Removing the

Valve Cap Assembly” & “Flushing Out the

Debris”.

FILL VALVE WILL NOT TURN ON.

• If float cup does not drop when flushing

the tank: Tighten

Leak Sentry

chain

by one link and then try flushing again.

Tighten by one link at a time until valve

turns on at flush. See “Hooking Up the

Leak

Sentry

Chain”.

WATER LEVEL IN BOWL IS TOO LOW.

• Move roller clamp to higher number.

LEAK SENTRY

WILL NOT LOCK FLOAT CUP.

• Make sure valve is set at 5 o’clock in tank.

• Make sure water drops below float cup

during flush. Raise the valve higher in

tank and reset water level.

• Device chain should be loose except

when lever is pushed to flush tank. See

“Hooking Up the Leak Sentry

Chain”.

• Untangle Leak Sentry

chain from screw

adjustment or device area.

CAUTION: Do not shove refill tube down overflow pipe.

This will cause loss of water from tank.

continued...

Removing

the Valve Cap

Assembly

Place shank

washer onto

threaded

shank of fill

valve. Flat

side up. Then

place fill valve

in tank.

Place valve in tank; do

not install. The Critical

Level mark – identified

on valve – should be

1 inch above the top of

the overflow pipe. This

is a plumbing code.

Remove fill valve from

tank to adjust height.

Adjust height of fill valve

by turning lower shank

in or out of the valve

body. Do not move lock

ring. It holds the valve

body and shank together

under pressure. Do not

interchange body with

old shank, as leaking

can occur.

Before installing the

valve, remove the valve

cap assembly. Push float

up with right hand (see

picture). Twist cap and

lever counterclockwise

1/8

th of a turn to unlock.

Let cap assembly hang

on float cup.

SHANK

WASHER

THREADED

SHANK

Simulate a leak by

slightly lifting flapper

chain to allow 3 or 4

inches of water to slowly

drain from tank. Fill

valve should not turn

on, but remain locked

and stay off.

If test fails go to

Troubleshooting section.

Make sure chain is free,

not tangled or caught.

LEAK SENTRY

CHAIN HOOK-UP

Lift tank lever all the way up inside tank and

hold it there. Pull Leak Sentry

chain until it

lifts the float cup all the way up the fill valve

shaft. Then connect chain & clip with no

slack in chain to the tank lever.

NOTE: Do not cross Leak Sentry

chain and

flapper chain. If lever has only one hole, then

attach to same hole.

If using the

Flush ’n Sparkle

cleaning system

the tank should

look like this

when setup

is complete.

Installing Fill Valve

LOCK-

NUT

CONE

WASHER

COUPLING

NUT

WATER

SHUTOFF

METAL/COPPER

FLARED TUBING

LOCK-

NUT

FLAT

WASHER

COUPLING

NUT

WATER

SHUTOFF

METAL FLANGED

TUBING

LOCK-

NUT

SPIRAL

CONE

WASHER

COUPLING

NUT

WATER

SHUTOFF

METAL SPIRAL

TUBING

LOCK-

NUT

COUPLING

NUT

WATER

SHUTOFF

VINYL/BRAIDED

CONNECTOR

PLASTIC OR METAL

COMPRESSION

BALL TUBING

CAUTION: Overtightening LOCKNUT or COUPLING

NUT could result in breakage and potential flooding.

CAUTION: DO NOT use CONE WASHER with

PLASTIC SUPPLY LINE or METAL SPIRAL TUBING.

DO NOT use plumber’s putty to seal these fittings. These parts must be used as illustrated to insure watertight connections.

Use Fluidmaster coupling nut and

cone washer to replace existing parts.

Water supply tube must extend 1/2 inch

inside threaded shank of valve.

Use existing coupling nut and

existing flat washer.

Use existing spiral

cone washer.

Do not use Fluidmaster's

coupling nut and the cone

washer on plastic or metal

tubing as shown.

Captive cone washer already

included. No additional

washers required.

Use chart to determine the appropriate assembly parts required to properly reconnect the water supply. Do not use plumber's putty to seal these

fittings (Teflon tape optional).

With correct washers in

place tighten coupling

nut. Hand-tighten only.

CAUTION: Do not use

Fluidmaster cone

washer with plastic

supply line or metal

spiral tubing.

Place fill valve

in tank. Align

fill valve nipple

to face right &

parallel with

back wall of

tank. Press

down on shank

while tightening

locknut. Hand-

tighten only.

1 2

START HERE 1
COMIENCE AQUÍ 2

Résumé du contenu

Page 1 - START HERE

+ORSHANK/CONEWASHERCOUPLINGNUTREFILL CLIPOR ANGLEADAPTERLOCKNUTRoller & HoseClampASSEMBLY PARTSLEAK SENTRY DEVICERoller & Hose Clamp42068Hose

Page 2 - COMIENCE AQUÍ

DISPOSITIVOLEAK SENTRYARANDELADE ESPIGA/CÓNICATUERCA DEACOPLAMIENTOSUJETADORDE RECARGAO ADAPTADOREN ÁNGULOCONTRATUERCAAbrazaderas de rodilloy de mangu

Commentaires sur ces manuels

Pas de commentaire

Fluidmaster 400LSRP14 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Non Fluidmaster 400LSRP14. Fluidmaster 400LSRP14 Installation Guide Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Fluidmaster 400LSRP14